Replacement rear knuckles for the GC/GD group, built to take a 2008 or later bolt-on wheel hub. A worn wheel bearing is replaced by unbolting the hub, without taking the rear suspension apart. Each knuckle style is set up for a particular hub, caliper and rotor combination, with stock geometry or 1.5" geometry correction, and single or dual calipers. Every set comes with a pair of trailing arms.

Before you order
Trailing arms are included. The knuckles come with their own trailing arms and do not work with stock trailing arms. The arm length is chosen with the trailing arm option.
Brake and drivetrain parts. Hubs, calipers, rotors, backing plates and axles are not included. See our knuckle configuration sheet for all specific part combinations.
E-brake. 2007 and older Subaru e-brake assemblies and backing plates do not fit these knuckles. A factory-style e-brake uses 2008 or later backing plates matched to the rotor, with the matching e-brake cable.
Which options do I need?
1. Knuckle Style
| Knuckle Style | Use case |
|---|---|
| Standard Geometry, 08 Hub, 07 WRX Caliper | Our smallest and simplest knuckle. Stock geometry, low weight, compact brakes and 15" wheel compatibility. For rally and similar builds |
| Standard Geometry, 08 Hub, 08 STI Caliper | Stock geometry with the larger STI rear brake. For street and performance cars that don't need geometry correction |
| 1.5" Geometry, 08 Hub, 08 STI Caliper | Corrected geometry for lowered street, track and performance cars, with the 2008-2014 STI caliper |
| 1.5" Geometry, 08 Hub, 08 STI and 07 WRX Dual Caliper | Corrected geometry with a second, independent caliper, for drift cars and hydraulic handbrakes. Subaru hubs |
| 1.5" Geometry, 370z Hub, 07 + 08 Subaru Caliper | Our 350Z/370Z rear frame with Subaru dual calipers. The lighter of the two 370Z hub dual-caliper styles |
| 1.5" Geometry, 370z Hub, Dual Nissan Caliper Mount | Our 350Z/370Z rear frame with Nissan dual calipers. Heavier, with more unsprung weight than the Subaru caliper style |
| CUSTOM | A configuration not listed here, built to order. Contact us before ordering |
2. Trailing arms
| Trailing arms | Length and requirements |
|---|---|
| Stock Length | Nothing extra. 20.375" hole to hole, the factory length. Works with any setup |
| +2" | 22.375" hole to hole. Needs our Rally or Track Trailing Arm Mounts, or our T-Bar or Geometry Special, which include mounts |
| XXXL | 27.5" hole to hole, 7.125" longer than stock. Needs our T-Bar or Geometry Special |
3. ABS
| ABS | Use case |
|---|---|
| Selected | Mounts for 2008 and later hall effect wheel speed sensors. The front sensors must also be 2008 or later. Subaru hubs only |
| Not selected | No rear ABS sensors, and all Nissan hub styles |
4. 2008 E-Brake (Subaru hubs)
| 2008 E-Brake | Use case |
|---|---|
| Selected | Factory-style e-brake, using 2008 or later backing plates matched to the rotor |
| Not selected | No factory e-brake. Includes a 10 mm shim that takes the place of the backing plate |
5. 350z/370z E-Brake (Nissan hubs)
| 350z/370z E-Brake | Use case |
|---|---|
| Selected | Adds the holes for 350Z or 370Z e-brake backing plates |
| Not selected | No Nissan e-brake. Includes a 16 gauge shim that takes the place of the backing plate |
Knuckle styles
Geometry
Standard Geometry keeps the stock suspension geometry.
1.5" Geometry moves the lateral link and trailing arm mounting points down 1.5" relative to the hub. This corrects the rear suspension geometry of a lowered car.
Single or dual caliper
The dual-caliper styles mount a second, independent caliper on the same rotor as the main caliper. It is used for a hydraulic handbrake on drift cars and similar builds. All dual-caliper styles have 1.5" geometry.
Hub
The 08 Hub styles take a 2008 or later Subaru rear hub. The 5x100 and 5x114.3 hubs share the same pilot diameter, 110 mm knuckle bolt pattern and 27-spline axle, so the wheel bolt pattern is set by the hub fitted, not by the knuckle.
The 370z Hub styles take a 350Z or 370Z rear hub. They are for our 350Z/370Z rear frame.
Trailing arms

Every set of knuckles includes a pair of straight trailing arms, made for the knuckle. They are double adjustable, use three-piece heim joints, and leave plenty of tire clearance. Stock trailing arms do not fit.
The +2" and XXXL lengths improve the rear suspension geometry. See the Trailing Arms guide and XXXL Trailing Arms guide for how the lengths compare.
Construction
- 3 mm and 4 mm Strenx plate
Fitment
A rear part for the GC/GD group:
- Impreza / WRX / STI 1993-2007 (GC, GF, GM, GD, GG)
- Legacy 1990-1999 (BC, BF, BJ, BD, BG, BK)
- Outback 1995-1999 (BD, BG, BK)
- Forester 1998-2008 (SF, SG)
Common questions
Can I use my stock trailing arms?
No. The knuckles come with their own trailing arms, in Stock Length, +2" or XXXL.
Does the knuckle set the wheel bolt pattern?
No. The 08 Hub styles take 5x100 and 5x114.3 Subaru hubs, so the bolt pattern comes from the hub. The 370z Hub styles are 5x114.3.
Which setups fit 15" wheels?
The 07 WRX Caliper style with a 290 mm rotor: the BRZ/86 rotor on 5x100, or the 2022+ WRX rotor on 5x114.3.
Will ABS work?
With the ABS option, 2008 or later Subaru hubs and 2008 or later front sensors. ABS doesn't work with the Nissan hubs.
Can I keep my 2007 or older e-brake?
No. 2007 and older Subaru backing plates and e-brake assemblies don't fit. Use 2008 or later backing plates matched to your rotor.
350Z or 370Z hub?
370Z. It has the larger, longer-lasting bearing and the larger 32-spline axle. The 370Z axles also work with a 350Z differential.
Which lateral links do I need with these knuckles?
Our Lateral Links with the TSS Rear Knuckles knuckle version for the sway links. Use 370z Length with our 350Z/370Z rear frame and stock 370Z axles. See the Lateral Links guide.
Can I get them powder coated?
Yes, as an option on the product page. Powder coating adds about 2-6 weeks. See Powder Coating.